|
We have board support packages (BSPs) and complete projects
available for various NXP Eval boards.
Different software packages are available for different
boards; the packages include some or all of the following components:
- embOS - real time OS / RTOS
- emWin - graphic software / GUI
- emFile - file system with support for NAND-, NOR- flashes, SD, CF cards, IDE and more
- emUSB - USB device stack with support for bulk, MSD, CDC, HID and more
Some packages are executable demos, which can not be modified; some packages
are trial versions, which come with the software in a library and the
application in source code form, as well as a project for the IDE that
has been used. Trial versions can usually be recompiled easily in less
than a minute if the required compiler and IDE is installed. The application
program can be modified, allowing intensive tests of the software. emWin
trial versions usually also contain a simulation environment which allows
test and recompilation on a PC.
Below is a list of supported Eval boards. The software
can easily be ported to other hardware platforms. If you are looking for
software for an Eval board not in this list, please get in touch with
us.
Supported Eval boards
IAR LPC2103 Eval board
|
|
Controller:
CPU:
Board main features:
- J-LINK on-chip with USB cable
- One serial port
- Reset button
- In-system programming (ISP) button
- Two user-defined buttons
- 16 fully configurable LEDs
- Power-on LED
- Lithium back-up battery and holder
- Breakout headers for all pins (suitable for mounting daughter boards)
- Small array of plated holes for prototyping
- Schematics included
- RoHS compliant
More |
IAR LPC2106 Eval board
| 
|
Controller:
CPU:
Board main features:
- LPC2106 MCU
- Two serial ports
- Reset button
- In-system programming (ISP) button
- Two user-defined buttons
- 16 fully configurable LEDs
- 20-pin JTAG interface connector
- Power-on LED
- Breakout headers for all pins (suitable for mounting daughter boards)
- 20x20 array of plated holes for prototyping
- Schematics included
- RoHS compliant
More |
IAR LPC2148 Eval board
|
|
Controller:
CPU:
Board main features:
- Audio circuit wth microphone jack and headphone jack
- Trace (MICTOR) connector mounted
- Two UARTs with drivers and DB9 connectors
- USB connector
- ETM routing
- Potentiometer connected to the ADC
- Two buttons
- One LED
- 2 x 16 LCD
- 20-pin JTAG interface connector
- SD connector for external memory
- 13x36 thru hole prototyping area
- Ready to run code example exercising on-chip peripherals
- Complete API for LCD
- Schematics included
- RoHS compliant
More |
IAR LPC2378 Eval board
|
|
Controller:
CPU:
Board main features:
- 1xRS232 serial port
- 1xCAN drivers and connectors
- Ethernet 100 Mbit
- SD/MMC card connector
- All LPC2378 port signals available on extension connectors
- Reset circuit with external control of Philips ISP utility via USB-RS232 virtual port
- Jumpers for ISP/RUN mode
- 2 user buttons
- USB connector
- Reset button
- Prototyping area 9x38
- JTAG connector
More |
Keil MCB2300 Eval board
|
|
Controller:
CPU:
Board main features:
- Two serial interfaces
- A speaker
- Analog input (via potentiometer)
- Two CAN interfaces
- LCD
- USB
- Ethernet
- Eight LEDs
More |
Embedded Artists LPC2468-16 OEM Eval board
|
|
Controller:
CPU:
OEM Board main features:
- 128 MB NAND Flash, 4 MB NOR Flash + 512 kB internal Flash
- 32 MB SDRAM + 96 KB internal RAM
- 16-bit data bus to SDRAM
- 100/10M Ethernet interface based on Micrel KSZ8001L Ethernet PHY
- 12.000 MHz crystal for CPU, 32.768 kHz crystal for RTC
- Two 100 pos Hirose expansion connector (FX8C-100), 0.6mm pitch
- 256 Kbit I2C E2PROM for storing non-volatile parameters
- Buffered 16-bit databus
Base Board main features:
- Two 100 pos, 0.6mm pitch Hirose FX8C-100 connectors for OEM Board
- Ethernet connector (RJ45)
- MMC/SD interface & connector
- JTAG connector
- Pads for ETM connector
- USB OTG interface & connector
- USB device interface & connector
- USB host interface & connector
- Full modem RS232 on UART #1
- CAN interface & connector
- Power supply, either via USB or external 9-15V DC
- 0.3F capacitor backup for RTC
- Color QVGA LCD expansion connector (serial and parallel interface options)
- WLAN module (IEEE802.11b) expansion connector
- 5 push-button keys (4 via I2C)
- 5 LEDs (via I2C)
- 2 Analog inputs
- USB-to-serial bridge on UART #0, and ISP functionality
- Reset push-button and LED
- Speaker output on v1.5 of OEM Base Board
- All OEM Board signals available on expansion connector/pads
More |
Copyright SEGGER Microcontroller GmbH & Co.KG. All
rights reserved.
For more information, please visit our web site
www.segger.com or contact us at info@segger.com
Last update:
April 15, 2008
|
Software
for NXP Eval boards
