|
We have board support packages (BSPs) and complete projects
available for various Atmel Eval boards.
Different software packages are available for different
boards; the packages include some or all of the following components:
- embOS - real time OS / RTOS
- emWin - graphic software / GUI
- emFile - file system with support for NAND-, NOR- flashes, SD, CF cards, IDE and more
- emUSB - USB device stack with support for bulk, MSD, CDC, HID and more
Some packages are executable demos, which can not be modified; some packages
are trial versions, which come with the software in a library and the
application in source code form, as well as a project for the IDE that
has been used. Trial versions can usually be recompiled easily in less
than a minute if the required compiler and IDE is installed. The application
program can be modified, allowing intensive tests of the software. emWin
trial versions usually also contain a simulation environment which allows
test and recompilation on a PC.
Below is a list of supported Eval boards. The software
can easily be ported to other hardware platforms. If you are looking for
software for an Eval board not in this list, please get in touch with
us.
 AT91 related products
   
 
Check out available AT91 related products such as embOS, emWin, emUSB, emFile with NAND Flash driver, J-Link, SAM-ICE and more
Supported Eval boards
Atmel AT91SAM9261 Eval board
| 
|
Controller:
CPU:
Board main features:
- 64 Mbytes of SDRAM
- 256 Mbytes of NAND Flash memory
- One Ethernet 100-base TX with three status LEDs
- Atmel AT73C213 Audio DAC
- 3.5" 1/4 VGA TFT LCD Module with TouchScreen and backlight
- DataFlash® SD/MMC Card slot
- One USB device port interface
- Two USB host port interfaces
- One DBGU serial communication port
More |
Cogent CSB737 Eval board
| 
|
Controller:
CPU:
Board main features:
- 64Mbyte 32-Bit Wide SDRAM
- 64Mbyte 16-Bit Wide Spansion S29GL512N
NOR Flash
- 512MByte 8-Bit Wide NAND Flash
- LCD Controller On-Chip 16-Bit RGB LCD
Controller up to 1024 x 768, 8MByte PSRAM Frame Buffer
- 2D Graphics On-Chip 2D Graphics Drawing
Engine
- 1x Debug RS232 (2-wire), plus one 4-wire
TTL UART and Two 2-wire TTL UARTS
- I2C, SPI x2, SSI and 4-Bit SDIO/MMC Controller
(Socket is off board)
- Unique ID via Electronic Serial Number
(ESN) in Spansion S29GL512N Flash
- On-Chip 10/100 Ethernet Controller with
Low Power LAN8700 PHY
- DS1339 RTC with External Battery Input
- 10 Dedicated GPIO (more may be available
depending upon Peripheral use)
- Dual USB 2.0, 12Mbit USB Host
- Single USB 2.0, 12Mbit USB device
- AC97 Audio Interface
- Single Channel CAN 2.0B interface, 1MBit
- Compact Flash Interface
- Standard ARM JTAG Interface
- 6V to 35V power input, On-Board 3.3V
Regulator (up to 2A is available off board)
More |
Atmel AT91RM9200 Eval board
|
|
Controller:
CPU:
Board main features:
- 8 Mbytes of parallel Flash memory
- Four banks of 2M x 32-bit SDRAM
- DataFlash or SD/MMC memory expansion socket
- Additional DataFlash® memory expansion socket
- Digital-to-Analog Converter (DAC) for a stereo audio signal
- Four communication ports (USB host and device, Ethernet, serial
and DBGU)
- Graphic controller with output to a standard VGA monitor
- JTAG/ICE, ETM and code test port interface
- Expansion connector
- Onboard prototype area
More |
Atmel AT91SAM7A3 Eval board
|
|
Controller:
CPU:
Board main features:
- USB device port interface
- One DBGU serial communication port
- JTAG/ICE debug interface connector
- Two serial CAN communication ports
- One serial LIN communication port
- One buffered analog input and PWM output
- One Power LED and four general-purpose LEDs
- One SD/MMC/DataFlash® card slot
- Expansion connector
- One Atmel 32 Mbit serial DataFlash® (AT45DB321C-CNC)
- One footprint for 3.6V lithium thionyl-chloride backup battery
More |
Atmel AT91SAM7SE Eval board
|
|
Controller:
CPU:
Board main features:
- 32 Mbytes of SDRAM memory
- 256 Mbytes of NAND Flash memory
- One USB device port interface
- One DBGU serial communication port
- One additional serial communication port with RTS/CTS handshake control
- One JTAG/ICE debug interface
- One Atmel AT73C213 Stereo Audio DAC
- One power LED and two general-purpose LEDs
- One joystick and two user input pushbuttons
- One Reset pushbutton
- Three expansion connectors (PIO A, PIO B, PIO C)
- One EBI expansion BGA-like footprint connector
More |
Atmel AT91SAM7S Eval board
|
|
Controller:
CPU:
Board main features:
- USB device port interface
- Two serial communication ports
- One Atmel Crypto memory
- JTAG/ICE debug interface
- Four buffered analog inputs
- Four general-purpose LEDs and pushbuttons
- Expansion connector
- Prototyping area
More |
Atmel AT91SAM7X Eval board
|
|
Controller:
CPU:
Board main features:
- Serial CAN communication ports
- Buffered analog input and PWM output
- One Reset pushbutton
- Power LED and general-purpose LEDs
- One DataFlash® card slot
- One expansion connector
- Atmel 32 Mbit serial DataFlash® (AT45DB321C-CNC)
- One footprint for Atmel Serial EEPROM (MN11)
- One joystick
- One JTAG/ICE debug interface
- Prototyping area
More |
Cogent CSB737 Eval board
|
|
Controller:
CPU:
Board main features:
- 64Mbyte 32-Bit Wide SDRAM
- 64Mbyte 16-Bit Wide Spansion S29GL512N NOR Flash
- 512MByte 8-Bit Wide NAND Flash
- LCD Controller On-Chip 16-Bit RGB LCD Controller up to 1024 x 768, 8MByte PSRAM Frame Buffer
- 2D Graphics On-Chip 2D Graphics Drawing Engine
- 1x Debug RS232 (2-wire), plus one 4-wire TTL UART and Two 2-wire TTL UARTS
- I2C, SPI x2, SSI and 4-Bit SDIO/MMC Controller (Socket is off board)
- Unique ID via Electronic Serial Number (ESN) in Spansion S29GL512N Flash
- On-Chip 10/100 Ethernet Controller with Low Power LAN8700 PHY
- DS1339 RTC with External Battery Input
- 10 Dedicated GPIO (more may be available depending upon Peripheral use)
- Dual USB 2.0, 12Mbit USB Host
- Single USB 2.0, 12Mbit USB device
- AC97 Audio Interface
- Single Channel CAN 2.0B interface, 1MBit
- Compact Flash Interface
- Standard ARM JTAG Interface
- 6V to 35V power input, On-Board 3.3V Regulator (up to 2A is available off board)
More |
Segger SAM7-MSD Eval board
|
|
Controller:
CPU:
Board main features:
- One communication port (USB device)
- One SD/MMC/DataFlash® card slot
- One JTAG debug interface
More |
Copyright SEGGER Microcontroller GmbH & Co.KG. All
rights reserved.
For more information, please visit our web site
www.segger.com or contact us at info@segger.com
Last update:
May 9, 2008
|
Software
for Atmel Eval boards
